How To Change A Low Beam Headlight On 2003 Honda Accord

The other day the driver's side depression axle headlight burnt out in my 2004 Honda Accord. This is a picture guide walking through the like shooting fish in a barrel steps to change out the light bulb.

What I used:

• flat screwdriver – medium size
• 10mm wrench
• Low-beam element of group vii bulbs (function# 9006)
• High-beam halogen bulbs (part# 9005)

Update (March 2021): Since writing this mail service, I have since tried LED bulbs, and honestly, they are much brighter and overall better. Also, if you have the alignment of the bulbs correct, you are not blinding on-coming traffic with these bulbs. I at present recommend the following LED bulbs over the previous halogen bulbs:

• Low-Beam LED Replacement Bulbs (Pack of ii) (part# 9006)
• High-Axle LED Replacement Bulbs (Pack of 2) (office# 9005)

Low-Beam Bulb Replacement

Hither is a side-by-side photograph of the 2 headlights on the Honda Accord. The high beams are on, in that configuration, both the low-beam and loftier-beam lights are illuminated. As you can run into in the photo on the correct, the depression axle is the outermost (furthest correct) calorie-free-seedling. The inner one is the high beam.

The replacement headlight bulbs for 2002-2007 Honda Accords depend on whether you lot are replacing the high-beam or depression-beam headlight. These bulbs are unlike and volition not fit into the mount for the contrary bulb, so brand sure you become the correct part number for what you need.

• Low-Beam LED Replacement Bulbs (Pack of 2) (part# 9006)
• High-Beam LED Replacement Bulbs (Pack of 2) (part# 9005)

The low-beam (part# 9006) bulb has a gray patch over the tip, I assume so it is non so vivid…

Okay, now that yous accept the correct seedling, let'southward go modify it!

2 Methods to Change the Bulb

The rider'due south side bulbs are relatively piece of cake to get at, just the commuter's side bulbs are a little more than cramped. For that reason, there are several different methods to get at the bulb so that you can perform the bandy.

Method ane: Get in through the Fender

Some people swear by this method, maxim it is much easier and quicker than method 2. It involves removing the protective plastic in the wheel well and accessing the bulb that mode.

Turn the steering wheel all the manner to the right to requite yourself as much room as possible to piece of work.

Also, yous will need a flat-bladed screwdriver.

Locate the plastic retaining clips on the inner role of the bike well that are holding the black protective plastic in identify. Yous will demand to remove about four of these.

Use the screwdriver to pry out the eye part of the clip.

Once the center part of the clip is out, the whole plug tin be pryed out. It is very easy to pause these, as I did shown in the photo below. If you've always taken off whatever sort of clips similar this earlier in the past, at least in my feel, about 50% of them finish up breaking and becoming loose or unuseable. This is a nice kit of a variety of replacement clips, in instance y'all try this method.

One time you have removed enough of the clips to pull dorsum the blackness plastic panel, you tin can wait in and run across the light bulb you need to change. In this case, the blackness bulb with the white connector (near the heart of the image) is the low-beam bulb.

I personally attempted this method and quit one-half-way through. Why? Because I bankrupt several of the retaining clips, it is bad-mannered working in a depression position around the tire, and information technology seemed that even when I did get the plastic all the manner off, it would all the same be a very tight fit to reach my arms in there. Therefore, I chose to consummate this job using method 2, and I recommend you do the same!

Method 2: Get in through the Hood

To access the driver'southward side headlight bulbs, pop the hood and prop it up. Nosotros volition remove the battery to admission the light bulbs.

1 – Remove the Battery

The beginning step is to remove the battery retaining bar. For this, apply a 10mm wrench.

Loosen the nut enough so that you can remove the hooks holding it down. Remove the retaining bar and set it aside.

Next, remove the negative bombardment cablevision. This requires a 10mm wrench.

After the negative cable is removed, and then remove the positive battery clamp.

Push button the bombardment cables aside and pull the battery out and fix information technology aside.

2 – Locate and Remove the Old Seedling

Now await down where the battery was toward the back of the headlights. You will see two connectors and there respective bulbs. I believe the high-beam connector is bluish, and the low-axle connector is white. In this case, I was replacing the low-axle bulb.

Take hold of the bulb body and give information technology a twist counter clockwise about i/eighth of a turn so pull it out. If it is besides tight, and you cannot get it loose, it sometimes helps to loosen the 3 Phillips head screws around the periphery.

Next, remove the old seedling by pressing the tab on the connector. Alternatively you can too apply a flat screwdriver to pry the tab upward to release the bulb.

Here is the old bulb removed. You can meet the broken filament.

Here is a shut-up of the broken filament, which I idea was kind of absurd to look at.

Take your new seedling and compare it to the old one, verifying that they are the aforementioned. Pay particular attention to the twist-lock tabs. The loftier-beam and depression-beam tabs are different, and they won't fit in each other's holder. Hither are the old and new bulbs next.

• Low-Axle LED Replacement Bulbs (Pack of 2) (function# 9006)
• High-Beam LED Replacement Bulbs (Pack of 2) (part# 9005)

iii – Put in the New Bulb

Advisedly take the new bulb and push it into the connector.

Note: Take care! Do not touch the glass part of the seedling! Touching the seedling tin contaminate the surface and reduce the lifetime of the seedling!

Press it into the connector until y'all hear a definite click.

Advisedly fit the new bulb back into position.

It will starting time in about the 10 o'clock position and once in, rotate it tightly into the 12 o'clock position. Basically the reverse of what y'all did to get it out.

At present that the bulb has been replaced, we tin can start putting things dorsum together.

4 – Put the Bombardment Back In

Advisedly set the battery back into place and re-connect the positive battery cable and tighten information technology up.

Then replace the negative bombardment cablevision and tighten that ane up.

Now put the bombardment retaining bar dorsum into place and hook the hooks into their eyelets. Then tighten upwardly the nut so that the battery is securely in place.

That's it! I promise you found this helpful!

Tools and Parts Referenced in this Article

• flat screwdriver – medium size
• 10mm wrench
• Low-Beam LED Replacement Bulbs (Pack of ii) (function# 9006)
• High-Axle LED Replacement Bulbs (Pack of 2) (part# 9005)
• kit with a variety of replacement clips

Source: https://practicalmechanic.com/2019/04/06/how-to-change-a-burnt-out-headlight-honda-accord/

Posted by: kunkelwhaeld.blogspot.com

Share this post